TP-LINK TL-R460 Manuale Utente

TL-R460 Cable/DSL Router User Guide Switch/HubTo WANTo LAN1WAN 234RESET（）XDSL Cable Ethernet、、 Figure 3-1 Hardware Installation of the TL-R460 C

TL-R460 Cable/DSL Router User Guide Chapter 4: Quick Installation Guide After connecting the TL-R460 router into your network, you should configur

TL-R460 Cable/DSL Router User Guide your PC and the router has been established. Figure 4-2 Failed result of Ping command If the result displ

TL-R460 Cable/DSL Router User Guide Note: If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools

TL-R460 Cable/DSL Router User Guide ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP. If you

TL-R460 Cable/DSL Router User Guide Chapter 5: Configuring the Router This chapter describes each web page's key functions. 5.1 login After

TL-R460 Cable/DSL Router User Guide Figure 5-1 Router Status 5.3 Quick Setup Please refer to Section 4.2: "Quick Installation Guide."5.

TL-R460 Cable/DSL Router User Guide  MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed. 

TL-R460 Cable/DSL Router User Guide This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, D

TL-R460 Cable/DSL Router User Guide Figure 5-5 WAN - Static IP You should type the following parameters into the spaces provided:  IP Address

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co., Ltd. Other br

TL-R460 Cable/DSL Router User Guide Click Logout to end 802.1x authentication. 3. If you choose PPPoE, you should enter the following parameters (

TL-R460 Cable/DSL Router User Guide that you wish to have the Internet connecting last unless a new link is requested. Caution: Sometimes the conne

TL-R460 Cable/DSL Router User Guide 5.4.3 MAC Clone You can configure the MAC address of the WAN port on this page, figure 5-8: Figure 5-8 MAC Ad

TL-R460 Cable/DSL Router User Guide 5.5.1 DHCP Settings The router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, whi

TL-R460 Cable/DSL Router User Guide DHCP Client attached to the router (figure 5-11): Figure 5-11 DHCP Clients List  Index - The index of the

TL-R460 Cable/DSL Router User Guide  Assigned IP Address - The IP address of the router reserved. To Reserve IP addresses: 1. Enter the MAC add

TL-R460 Cable/DSL Router User Guide Figure 5-14 Virtual Servers  Service Port - The numbers of External Ports. You can type a service port or a

TL-R460 Cable/DSL Router User Guide 3. Click the Save button. To delete a service entry: 1. Clear the entry's all information except for the

TL-R460 Cable/DSL Router User Guide  Trigger Port - The port for outgoing traffic. An outgoing connection using this port will "Trigger"

TL-R460 Cable/DSL Router User Guide Note: 1. When the trigger connection is released, the according opening ports will be closed. 2. Each rule a

Package contents... 1 Chapter 1: About thi

TL-R460 Cable/DSL Router User Guide  Enable UPnP - UPnP can be enabled or disabled by clicking the Enable or Disable button. As allowing this may

TL-R460 Cable/DSL Router User Guide Figure 5-19 Firewall Settings  Enable Firewall - The general firewall switch is on or off.  Enable IP Add

TL-R460 Cable/DSL Router User Guide To disable the IP Address Filtering feature, keep the default setting, Disabled. To set up an IP Address Filter

TL-R460 Cable/DSL Router User Guide Click the Disable All button to disable all entries. Click the Delete All button to delete all entries You

TL-R460 Cable/DSL Router User Guide Figure 5-23 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these

TL-R460 Cable/DSL Router User Guide 5.7.4 MAC Filtering Like the IP Address Filtering page, the MAC Address Filtering page (shown in figure 5-24) a

TL-R460 Cable/DSL Router User Guide Click the Enable All button to enable all entries. Click the Disable All button to disable all entries. Cli

TL-R460 Cable/DSL Router User Guide router's password. After successfully entering the password, you will be able to access the router's

TL-R460 Cable/DSL Router User Guide value between 5 ~ 3600 packets. When the current UPD-FLOOD Packets numbers are beyond the set value, the router

TL-R460 Cable/DSL Router User Guide Figure 5-29 Static Routing To add static routing entries: 1. Enter the following data:  Destination IP Addr

5.9.1 Oray.net DDNS ... 36 5.9.2 Comexe.cn DDNS...

TL-R460 Cable/DSL Router User Guide 5.9.1 Oray.net DDNS If your selected dynamic DNS Service Provider is www.oray.net. The page shown in figure 5

TL-R460 Cable/DSL Router User Guide Figure 5-31 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the domain names

TL-R460 Cable/DSL Router User Guide 5.10.1 Time You can set the time manually or get GMT from the Internet for the router on this page (shown in fi

TL-R460 Cable/DSL Router User Guide New firmware versions are posted at www.tp-link.com and can be downloaded for free. If the router is not experi

TL-R460 Cable/DSL Router User Guide Figure 5-36 Reboot the router Click the Reboot button to reboot the router. Some settings of the router wil

TL-R460 Cable/DSL Router User Guide 5.10.6 Log This page (shown in figure 5-38) allows you to query the Logs of the router. Figure 5-38 System

TL-R460 Cable/DSL Router User Guide Statistics Table: IP Address The IP address displayed with statistics PacketsThe total amount of packets rece

TL-R460 Cable/DSL Router User Guide Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the A

TL-R460 Cable/DSL Router User Guide your browser, and then click "MAC Clone" submenu link. On the "MAC Clone" page, if your PC’

TL-R460 Cable/DSL Router User Guide Figure A-5 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port

TL-R460 Cable/DSL Router User Guide Package contents The following contents should be found in your box:  One TL-R460 Cable/DSL Router  One AC

TL-R460 Cable/DSL Router User Guide Appendix B: Configuring the PCs In this section, we’ll introduce how to install and configure the TCP/IP corre

TL-R460 Cable/DSL Router User Guide window that appears. An example is shown in the following figure: Figure B-3 Configuration tab 3) Click on P

TL-R460 Cable/DSL Router User Guide Figure B-5 Gateway tab c. Choose Disable DNS on the DNS configuration tab, as shown in the following figure:

TL-R460 Cable/DSL Router User Guide Figure B-7 IP Address tab b. Type the router’s LAN IP address (the default IP is 192.168.1.1) into the New g

TL-R460 Cable/DSL Router User Guide click Add button. Shown below: Figure B-9 DNS Configuration tab Now, all the configurations are finished,

TL-R460 Cable/DSL Router User Guide Appendix C: Specifications General Standards IEEE 802.3, 802.3u Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SN

TL-R460 Cable/DSL Router User Guide Appendix D: Glossary  DDNS (Dynamic Domain Name System) - The capability of assigning a fixed host and do

TL-R460 Cable/DSL Router User Guide Appendix E: Contact Information For help with the installation or operation of the TP-LINK TL-R460 Cable/DSL R

TL-R460 Cable/DSL Router User Guide Chapter 1: About this Guide Thank you for choosing the TL-R460 Cable/DSL Router. This router provides dedicate

TL-R460 Cable/DSL Router User Guide Chapter 2: Introduction 2.1 Overview of the Router The TL-R460 Cable/DSL Router integrates a 4-port switch, fi

TL-R460 Cable/DSL Router User Guide indicate connections. Viewed from left to right. Table 2-1 describes the LEDs on the front panel of the router.

TL-R460 Cable/DSL Router User Guide Chapter 3: Connecting the Router 3.1 System Requirements  Broadband Internet Access Service (DSL/Cable/Ether